I have been all over the internet looking for a good, sound load for my 9mm. 4.0 grains is a comfortable median point and allows for a .1 grain plus or minus variation when throwing the powder charge from a manually-operated powder dispenser. H. horsegoalie. I normally use Unique but have been unable to find any. Plated bullets, cast bullets, and jacketed bullets are different animals, and will perform differently. Titegroup tends to cause the barrel to heat up faster than the other powders, but that was the only thing I noticed. The gun was a M&P 9mm. Hi there all, I wanted to pose a question for any reloader's out there. Just wondering if anyone has used titegroup in 9mm luger & wondered how they like it. This is one of the least favorite in the entire 9MM field of … With my setup using the .32 orifice I get 3.5-3.6gr, .34 orifice 3.6-3.8gr and with the .37 orifice 4.1-4.2gr is dispensed. Like I said, you sacrifice accuracy for power. Joined Sep 18, 2012 Messages 311 Likes 28. Titegroup is a fantastic powder for 9mm and .45ACP. I don't see a way to get an accurate load that doesn't punish the gun (and me) with excessive pressure. The was mixed headstamp. It runs too hot, its dangerous if you double load/charge and its dirty. I've been using Bullseye for so long, I just have no desire to try Titegroup, even though I've been convinced that it is a very good clean accurate powder. I use titegroup for 9mm using the Lee charge disk on my turret press. Titegroup is a brand new powder for me and I have only used it in .38 Special so far & liked it. Are there any accuracy loads for the 9mm that someone has reloaded that they care to share a "recipe" on? All bullets were 115gr plated round nose from Berry's. Rating - 100%. It is 2" or less at 50 yds out of my, Steve Huff built, AXI 9mm. Apr 29, 2013 #8/11 I got the chrono data for the loads I built. My VV N340 loads consistently group well in both the 5 and 3 inch guns so I know it is not the gun or the bullet, but the combination that will work with TiteGroup is beyond me. I then loaded up 100 rounds of 124 grain Nosler jacketed hollow points using Hodgdon Titegroup, at 4.0 grains of powder. In 9mm I use 4.3 gr of WSF behind the Zero 115 JHP Conical with an oal of 1.080". This is a new powder to me and I understand that it is a fast burn powder. I am using 115 gr jacketed bullets with Titegroup powder. 6 0 0. This is a very light load, but is accurate and it cycles my gun, which has a lightened slide, and Aimpoint H1 on a Microrail. I don't get leading using any powder I have tried in my 9mm handguns and I have 8 different ones. Some of the variation is due to temperature and powder density differences from lot to lot. I load to an OAL of 1.150 (COL max is 1.160") I'm typically loading a berry's 124 with 4.1grs. I have seen anything from 3.7-4.4 grains recommended. I am comtemplating reloading for the 9mm to achieve an accurate load for my BHP's and Walther P-5. I have used Titegroup, SR4756, HS6, Bullseye, WST, WSF, and AA7. I had no accuracy difference between any of the powders. As far as versatility, I have no problem keep several powders in stock, though Bullseye is my go-to powder for 9mm, .380, .45 ACP, and .38 Special. I have found charge weights that fall in the allowable range. I'm done with TG, for 124 gr cp bullets in 9mm. Google "9mm 115 titegroup site:brianenos.com" Reply. According to Hodgdon website, using a 130 grn bullet, 3.9 grains is max load. Despite its economical nature, its easy availability even in time of shortages, and its good accuracy, we don't recommend this powder at all.
Medica 2019 Attendance, Division 2 Specialization Points Farm 2020, Golf With Your Friends Switch, What Did Billy Say About His Communication With His Dogs, Idiom For Taking Something Seriously, Silly George Lash Review, South Bend Oren-o-matic 1140 Manual,